ProSLIC failed to powerup

I have an old Asterisk box at home with just a TDM-800 board running. Some of the ports went off and I see this on boot

[   17.647027] IPv6: ADDRCONF(NETDEV_CHANGE): enp4s0: link becomes ready
[   18.634909] dahdi: loading out-of-tree module taints kernel.
[   18.636302] dahdi: module verification failed: signature and/or required key missing - tainting kernel
[   18.639032] dahdi: Version: 2.11.1
[   18.641693] dahdi: Telephony Interface Registered on major 196
[   20.729054] wctdm24xxp 0000:04:01.0: ProSLIC on module 4 failed to powerup within 501 ms (0 mV only)

 -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
[   20.729062] wctdm24xxp 0000:04:01.0: Unable to do INITIAL ProSLIC powerup on module 4
[   21.429049] wctdm24xxp 0000:04:01.0: ProSLIC on module 4 failed to powerup within 501 ms (0 mV only)

 -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
[   21.429058] wctdm24xxp 0000:04:01.0: Unable to do INITIAL ProSLIC powerup on module 4
[   21.429062] wctdm24xxp 0000:04:01.0: Port 5: FAILED FXS (FCC)
[   22.146041] wctdm24xxp 0000:04:01.0: ProSLIC on module 5 failed to powerup within 504 ms (0 mV only)

 -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
[   22.146049] wctdm24xxp 0000:04:01.0: Unable to do INITIAL ProSLIC powerup on module 5
[   22.841038] wctdm24xxp 0000:04:01.0: ProSLIC on module 5 failed to powerup within 502 ms (0 mV only)

 -- DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
[   22.841046] wctdm24xxp 0000:04:01.0: Unable to do INITIAL ProSLIC powerup on module 5
[   22.841050] wctdm24xxp 0000:04:01.0: Port 6: FAILED FXS (FCC)
[   25.270055] wctdm24xxp 0000:04:01.0: Port 1: Installed -- AUTO FXO (FCC mode)
[   25.270062] wctdm24xxp 0000:04:01.0: Port 2: Installed -- AUTO FXO (FCC mode)
[   25.270066] wctdm24xxp 0000:04:01.0: Port 3: Installed -- AUTO FXO (FCC mode)
[   25.270070] wctdm24xxp 0000:04:01.0: Port 4: Installed -- AUTO FXO (FCC mode)
[   25.270074] wctdm24xxp 0000:04:01.0: Port 5: Installed -- AUTO FXS/DPO
[   25.270077] wctdm24xxp 0000:04:01.0: Port 6: Installed -- AUTO FXS/DPO
[   25.270081] wctdm24xxp 0000:04:01.0: Port 7: Installed -- AUTO FXS/DPO
[   25.270085] wctdm24xxp 0000:04:01.0: Port 8: Installed -- AUTO FXS/DPO
[   25.270910] wctdm24xxp 0000:04:01.0: Found a Wildcard TDM: Wildcard TDM800P (0 BRI spans, 8 analog channels)
[   25.453979] dahdi_devices pci:0000:04:01.0: local span 1 is already assigned span 1
[   25.534675] dahdi_echocan_mg2: Registered echo canceler 'MG2'

Can the power to the TDM card fail on just 2 of the 4 ports? Could it be possibly fixed? I have no access to other board to test :frowning:

It is working except for 2 of the analog extensions being off

Contact the card vendor. This forum does not support commercial circuit switched hardware.

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.