I have a TDM410P connected to my machine and an analog telephone, alcatel temporis 350
My TDM410 has two channels one FXS and one FXO (1 and 4 respectively).
Thing is that when I connect analog phone to FXS it doesnt get power.
I’ve checked in my system :
lspci | grep Digium
05:08.0 Ethernet controller: Digium, Inc. Wildcard TDM410 4-port analog card (rev 11)
And card seems to be already working…
I’ve configured dahdi’s system.conf, also chan_dahdi.conf
But phone continues with no power… I’m wondering what should I check to know how can I make phone get at least power (to know if the card is well functioning at least)
Regards
Some more info maybe can help out for the solution
With dahdi_tools I see:
Wildcard TDM410P Board 1
Current Alarms: No alarms.
Sync Source: Internally clocked
IRQ Misses: 0
Bipolar Viol: 0
Tx/Rx Levels: 0/ 0
Total/Conf/Act: 4/ 2/ 0
Here says: 2 conf of a total of 4 ports. In the first I have a green FXS and in the last a red FXO. By the way I have both connected to cat3 Rj11 cables and tried both to connect to my alcatel temporis 350 neither connect. I’ve tried to connect the alcatel directly to the analog line to check if problem was telephone, and works ok so telephone is not the problem, and I want to know if card can be the problem or maybe configuration
Some info about /etc/dahdi
In modules only have loaded:
Digium TDM2400P/AEX2400: up to 24 analog ports
Digium TDM800P/AEX800: up to 8 analog ports
Digium TDM410P/AEX410: up to 4 analog ports
wctdm24xxp
In system.conf just:
fxsks=1
fxoks=4
loadzone=es
defaultzone=es
echocanceller=mg2,1
echocanceller=mg2,4
Rebooted the system, asterisk works by default with sip phones.
But Alcatel Temporis is dead. Doesn’t get power.
More info:
The TDM410P is plugged to the molex conector
I’ve checked out that it is getting power:
10000horas.com/asterisk/files/20 … imetro.jpg
And also I’ve tried with a different and more powerful power supply:
10000horas.com/asterisk/files/20 … enador.jpg
But still cannot get this to work. I look at the kernel boot record with dmesg: this output:
dahdi: Telephony Interface Registered on major 196
dahdi: Version: 2.3.0.1
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
wctdm24xxp 0000:05:08.0: PCI INT A -> Link[APC3] -> GSI 18 (level,
low) -> IRQ 18
wctdm24xxp 0000:05:08.0: ProSLIC on module 0 failed to powerup within
510 ms (0 mV only)
– DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
wctdm24xxp 0000:05:08.0: Unable to do INITIAL ProSLIC powerup on
module 0
wctdm24xxp 0000:05:08.0: ProSLIC on module 0 failed to powerup within
510 ms (0 mV only)
– DID YOU REMEMBER TO PLUG IN THE HD POWER CABLE TO THE TDM CARD??
wctdm24xxp 0000:05:08.0: Unable to do INITIAL ProSLIC powerup on
module 0
wctdm24xxp 0000:05:08.0: Port 1: FAILED FXS (FCC)
wctdm24xxp 0000:05:08.0: Port 2: Not installed
wctdm24xxp 0000:05:08.0: Port 3: Not installed
wctdm24xxp 0000:05:08.0: Port 4: Installed — AUTO FXO (FCC mode)
I’ve tried configuring the FXS in nearly all the channels with no success
I’m stucked with this problem 