Modprobe error

Asterisk Asterisk Support
1

hi
i am using slakware 10.2 with kernal 2.6
i am following all the instruction step by step
in the scratch_install document.
I had installed asrerisk 1.2.9.1 and working fine.
now when i install module for my digium x100p card.
i got error

root@nitin:/usr/src/asterisk/asterisk-1.2.9.1# modprobe zaptel
root@nitin:/usr/src/asterisk/asterisk-1.2.9.1# modprobe wcfxo
/lib/modules/2.4.31/misc/wcfxo.o: init_module: No such device
/lib/modules/2.4.31/misc/wcfxo.o: Hint: insmod errors can be caused by incorrec t module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.31/misc/wcfxo.o: insmod /lib/modules/2.4.31/misc/wcfxo.o faile d
/lib/modules/2.4.31/misc/wcfxo.o: insmod wcfxo failed
root@nitin:/usr/src/asterisk/asterisk-1.2.9.1#

2

try to install zaptel before you install asterisk

3

hi
i have install libpri
then zaptel
then asterisk

and when try to install module for digium card x100p
then i got this error

thanks in advance

4

what does zttool show?
what is the output of ztcfg -vvvv?

5

hi,
as you ask for the output
what is the output of ztcfg -vvvv?
its not work.
how can i configure when i got error in
modprobe zaptel
modprobe wcfxo

thanks

6

are you sure zaptel is loading before you try loading the wcfxo module ? also, what’s the outout of lspci -v

7

hi

now i try my digium x100p card on debian 3.1 with kernal 2.6
and asterisk 1.2…9.1
when i try
modprobe zaptel
modprobe wcfxo
it neither shows any error nor any output.
the output of lspci -v is

0000:00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM Controll er/Host-Hub Interface (rev 03)
Subsystem: Giga-byte Technology GA-8PE667 Ultra
Flags: bus master, fast devsel, latency 0
Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [1105]

0000:00:02.0 VGA compatible controller: Intel Corp. 82845G/GL[Brookdale-G]/GE Ch ipset Integrated Graphics Device (rev 03) (prog-if 00 [VGA])
Subsystem: Giga-byte Technology: Unknown device 2562
Flags: bus master, fast devsel, latency 0, IRQ 169
Memory at e0000000 (32-bit, prefetchable) [size=128M]
Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1

0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) US B UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology: Unknown device 24c2
Flags: bus master, medium devsel, latency 0, IRQ 169
I/O ports at d800 [size=32]

0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) US B UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology: Unknown device 24c2
Flags: bus master, medium devsel, latency 0, IRQ 177
I/O ports at d000 [size=32]

0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) US B UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology: Unknown device 24c2
Flags: bus master, medium devsel, latency 0, IRQ 185
I/O ports at d400 [size=32]

0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology: Unknown device 5006
Flags: bus master, medium devsel, latency 0, IRQ 193
Memory at e8180000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2

0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 82) (prog-if 00 [Norm al decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e80fffff

0000:00:1f.0 ISA bridge: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) LPC Bridge (rev 0 2)
Flags: bus master, medium devsel, latency 0

0000:00:1f.1 IDE interface: Intel Corp. 82801DB/DBL (ICH4/ICH4-L) UltraATA-100 I DE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology GA-8PE667 Ultra
Flags: bus master, medium devsel, latency 0, IRQ 185
I/O ports at
I/O ports at
I/O ports at
I/O ports at
I/O ports at f000 [size=16]
Memory at 10000000 (32-bit, non-prefetchable) [size=1K]

0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Contr oller (rev 02)
Subsystem: Giga-byte Technology GA-8PE667 Ultra
Flags: medium devsel, IRQ 201
I/O ports at 5000 [size=32]

0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4 -L/ICH4-M) AC’97 Audio Controller (rev 02)
Subsystem: Giga-byte Technology GA-8PE667 Ultra
Flags: bus master, medium devsel, latency 0, IRQ 201
I/O ports at e000 [size=256]
I/O ports at e400 [size=64]
Memory at e8181000 (32-bit, non-prefetchable) [size=512]
Memory at e8182000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

0000:01:00.0 Modem: PCTel Inc: Unknown device 2189 (rev 04) (prog-if 00 [Generic ])
Subsystem: PCTel Inc: Unknown device 1002
Flags: bus master, stepping, medium devsel, latency 32, IRQ 185
Memory at e8000000 (32-bit, non-prefetchable) [size=4K]
I/O ports at c000 [size=256]
Capabilities: [80] Power Management version 2

0000:01:02.0 Communication controller: Motorola: Unknown device 5608
Subsystem: Motorola: Unknown device 0000
Flags: bus master, medium devsel, latency 32, IRQ 209
I/O ports at c400 [size=256]
Memory at e8001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2

0000:01:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C /8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 217
I/O ports at c800 [size=256]
Memory at e8002000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2

what this mean!!!

thanks

8

[quote=“gangiyanrohit”]now i try my digium x100p card on debian 3.1 with kernal 2.6
and asterisk 1.2…9.1
when i try
modprobe zaptel
modprobe wcfxo
it neither shows any error nor any output.
[/quote]
if you’re not getting any error that’s ok. if you want verbose output when modprobe’ing use “modprobe -v wcfxo”

now you’ve got the module loaded what does ztcfg -vvv return ? … i’ll assume you have zapata.conf setup !