Hi all,
I get digium free fax license.
where i can put the key code ?
Becouse when make command in cli: fax show licenses appears free fax licenses 0
total licenses port 0
how i can fixed ? 
Regards,
Howdy,
See the Installation Procedure section in the README:
downloads.digium.com/pub/telephony/fax/README
Hi,
I read th README in General Notes i don´t have licenses in : var/lib/asterisk/ 
Regards,
Then it’s likely the register application was not run successfully against the key.
how i can fixed ?
ipbx*CLI> fax show capabilities
Registered FAX Technology Modules:
Type : DIGIUM
Description : Digium FAX Driver
Capabilities : SEND RECEIVE T.38 G.711 MULTI-DOC
1 registered modules
ipbx*CLI> fax show licenses
Fax Licensing Information
Free fax licenses: 0
Total licensed ports: 0
ipbx*CLI> fax show settings
FAX For Asterisk Settings:
ECM: Enabled
Status Events: On
Minimum Bit Rate: 2400
Maximum Bit Rate: 14400
Modem Modulations Allowed: V17,V27,V29
FAX Technology Modules:
DIGIUM (Digium FAX Driver) Settings:
Maximum T.38 Packet Delay: 800
T.38 Session Packet Capture: Off
G.711 Session Audio Capture: Off
ipbxCLI> fax show se
session sessions settings
ipbxCLI> fax show ses
session sessions
ipbx*CLI> fax show sessions
Current FAX Sessions:
Channel Tech FAXID Type Operation State File(s)
0 FAX sessions
fax show hostid
Host-ID: 4d:2e:3a:8e:c7:40:c4:d3:5f:4e:e9:c7:de:b5:4a:df:b7:80:a7:34
Regards,
how i can fixed ?
I have the number of order !
Regards,
Hi all,
I can give more information about my problem !
module load res_fax_digium.so
Loaded res_fax_digium.so
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2536 load_module: Digium FAX technology module version 11.0_1.3.1, Copyright © 2008-2009 Digium, Inc.
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2539 load_module: This module is supplied under a commercial license granted by Digium, Inc.
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2540 load_module: Please see the full license text supplied by the accompanying
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2541 load_module: “register” utility, or ask for a copy from Digium.
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2544 load_module: This product includes software developed by the OpenSSL Project
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2545 load_module: for use in the OpenSSL Toolkit. (openssl.org/)
[Mar 26 16:43:31] NOTICE[12004]: res_fax_digium.c:2546 load_module: Copyright © 1998-2008 The OpenSSL Project
== res_fax_digium Host-ID: 4d:2e:3a:8e:c7:40:c4:d3:5f:4e:e9:c7:de:b5:4a:df:b7:80:a7:34
[Mar 26 16:43:31] WARNING[12004]: res_fax_digium.c:2494 handle_cp: Failed to initialize res_fax_digium copy protection!
== res_fax_digium limiting support to 0 sessions
– Registered handler for ‘DIGIUM’ (Digium FAX Driver)
== Manager registered action FaxLicenseStatus
== Manager registered action FaxLicenseList
Loaded res_fax_digium.so => (Digium G.711 and T.38 FAX Technologies (optimized for generic_64))
guys can help me ?
Did you follow 1.2 and 1.3 from Installation Procedure in the README?
Hi ,
yes i do,
See cd /root/
anaconda-ks.cfg benchfax Documentos Imagens install.log.syslog Música register
Ãrea de Trabalho Download install.log Modelos Público VÃdeos
I use centos 6.5 64 bits may be the problem ?
Regards,
And you ran the register utility as root, selected your product type, input your key and it finished without error, and it didn’t generate the .lic files in /var/lib/asterisk/licenses ?
hi
ok i all ready run /root/licenses and now appears licenses in /var/lib/asterisk/licenses 
but now appears error when i run /root/benchfax,
[root@ipbx ~]# /root/benchfax
/root/benchfax: line 1: syntax error near unexpected token newline' /root/benchfax: line 1:'
[root@ipbx ~]#
Regards,
skip it. Just get the binary that’s appropriate for your cpu type.
Hi ,
see these :
/root/benchfax-1.1.0-x86_64
benchfax version 1.1.0
Use the ‘-l’ option to see license information for software
included in this program.
Running test using CCITT FAX test page, US letter size, 204x196 resolution, MMR encoding, ECM enabled and V.17 (14.4kbps) modem
NOTE: Each individual test could take 20 seconds or longer; be patient.
Test run 1 for flavor ‘generic’ used 212 milliseconds of CPU time.
Test run 2 for flavor ‘generic’ used 196 milliseconds of CPU time.
Test run 3 for flavor ‘generic’ used 242 milliseconds of CPU time.
Test run 4 for flavor ‘generic’ used 197 milliseconds of CPU time.
Test run 5 for flavor ‘generic’ used 209 milliseconds of CPU time.
Test run 1 for flavor ‘nocona’ used 230 milliseconds of CPU time.
Test run 2 for flavor ‘nocona’ used 206 milliseconds of CPU time.
Test run 3 for flavor ‘nocona’ used 184 milliseconds of CPU time.
Test run 4 for flavor ‘nocona’ used 214 milliseconds of CPU time.
Test run 5 for flavor ‘nocona’ used 201 milliseconds of CPU time.
Test run 1 for flavor ‘core2’ used 208 milliseconds of CPU time.
Test run 2 for flavor ‘core2’ used 196 milliseconds of CPU time.
Test run 3 for flavor ‘core2’ used 215 milliseconds of CPU time.
Test run 4 for flavor ‘core2’ used 207 milliseconds of CPU time.
Test run 5 for flavor ‘core2’ used 220 milliseconds of CPU time.
Test run 1 for flavor ‘opteron’ used 193 milliseconds of CPU time.
Test run 2 for flavor ‘opteron’ used 225 milliseconds of CPU time.
Test run 3 for flavor ‘opteron’ used 231 milliseconds of CPU time.
Test run 4 for flavor ‘opteron’ used 229 milliseconds of CPU time.
Test run 5 for flavor ‘opteron’ used 207 milliseconds of CPU time.
Test run 1 for flavor ‘opteron-sse3’ used 195 milliseconds of CPU time.
Test run 2 for flavor ‘opteron-sse3’ used 218 milliseconds of CPU time.
Test run 3 for flavor ‘opteron-sse3’ used 207 milliseconds of CPU time.
Test run 4 for flavor ‘opteron-sse3’ used 195 milliseconds of CPU time.
Test run 5 for flavor ‘opteron-sse3’ used 206 milliseconds of CPU time.
Test run 1 for flavor ‘barcelona’ used 229 milliseconds of CPU time.
Test run 2 for flavor ‘barcelona’ used 217 milliseconds of CPU time.
Test run 3 for flavor ‘barcelona’ used 229 milliseconds of CPU time.
Test run 4 for flavor ‘barcelona’ used 239 milliseconds of CPU time.
Test run 5 for flavor ‘barcelona’ used 221 milliseconds of CPU time.
Results:
Average for flavor ‘generic’ is 206 milliseconds of CPU time.
Average for flavor ‘nocona’ is 207 milliseconds of CPU time.
Average for flavor ‘core2’ is 210 milliseconds of CPU time.
Average for flavor ‘opteron’ is 220 milliseconds of CPU time.
Average for flavor ‘opteron-sse3’ is 202 milliseconds of CPU time.
Average for flavor ‘barcelona’ is 226 milliseconds of CPU time.
Recommended flavor for this system is ‘opteron-sse3’ with an average of 202 mill iseconds of CPU time.
[root@ipbx ~]#
this is good or bad ?
Regards,
Dunno. That’s what your system returned. What it means is that the differences between the various flavors is very small.
Hi,
i thing i could ?!
fax show stats
FAX Statistics:
Current Sessions : 0
Reserved Sessions : 0
Transmit Attempts : 0
Receive Attempts : 0
Completed FAXes : 0
Failed FAXes : 0
Digium G.711
Licensed Channels : 1
Max Concurrent : 0
Success : 0
Switched to T.38 : 0
Canceled : 0
No FAX : 0
Partial : 0
Negotiation Failed : 0
Train Failure : 0
Protocol Error : 0
IO Partial : 0
IO Fail : 0
Digium T.38
Licensed Channels : 1
Max Concurrent : 0
Success : 0
Canceled : 0
No FAX : 0
Partial : 0
Negotiation Failed : 0
Train Failure : 0
Protocol Error : 0
IO Partial : 0
IO Fail : 0
have same information to configure in dialplan to send and received fax ?
Regards,
There is an Administrator manual [1] linked from the product page [2].
[1]: docs.digium.com/FAX/fax_for_aste … manual.pdf
[2]: digium.com/en/products/softw … r-asterisk
Hi , all
I try to use these in my ivr Dialplan ; exten = fax,1,Goto(fax-rx,receive,1)
i received the fax , but if i have guys from out side to call us the call go to volte sempre
how i can fixed ?
[open]
exten => s,1,Answer()
exten => s,n,WaitExten(0.5)
exten = fax,1,Goto(fax-rx,receive,1)
exten => s,n,Background(bem)
exten => s,n,WaitExten(2)
exten => 1,1,Goto(default,num,1)
exten => 2,1,Goto(default,num,1)
exten => 3,1,Goto(default,num,1)
exten => 4,1,Goto(default,num,1)
exten => 5,1,Goto(default,num,1)
exten => 6,1,Goto(default,num,1)
exten => *,1,Goto(s,1)
exten => t,1,Set(NUMTIMEOUTS=$[${NUMTIMEOUTS}+1]})
exten => t,2,Gotoif($["{NUMTIMEOUTS}" < “3”]?s,3)
exten => t,3,Background(Voltesempre)
exten => t,4,Hangup()
exten => i,1,Playback(opcao_invalida)
exten => i,n,Goto(s,1)
exten => s,n,Hangup()
Regards,
Hi All,
ok already fixed the problem fax incoming call in ivr.
wich one comand i can use for send a fax ? it’s possibol use a email for send fax?
i need to do in centos 6.5 ?
Regards,