I’m sure this will work if I (a * newb) can figure it out.
Ok, I’m using a Sangoma A101 T-1 card to connect to a Mitel Sx-2000 via a T-1 connections. I have loaded all config files and drivers, but they still do not see each other.
Can anyone point me to a tutorial or wiki that has this info, or let me know where the catch is?
TIA
Rquick
I have the two links up, but I don’t think all the digits are passing, and I get a hell of alot of static.
Here are all my settings:
Mitel:
| DIGITAL E AND M TRUNK CIRCUIT DESCRIPTOR ASSIGNMENT |
| |
| Trunk Circuit Descriptor Number: 10 |
| |
| Descriptor | Value |
|------------------------------------------------------------------------------|
| |
| Incoming and Outgoing Parameters |
| |
|Call Collision Handling (AT&T/Normal). . . . . . . . . . . AT&T |
| AT&T Call Collision Handling (Backoff/Nobackoff). . . . Backoff |
|Ignore Far End Disconnect (Yes/No) . . . . . . . . . . . . No |
|Release Acknowledge Timer (40-2400 units) (unit=50 msec) . 80 |
|Address Signalling (Loop/DTMF) . . . . . . . . . . . . . . DTMF |
|Disconnect Timer (100-900 msec). . . . . . . . . . . . . . 300 |
| |
| Incoming Parameters |
| |
|Incoming Start Type (Immediate/Wink/Delay) . . . . . . . . Wink |
|Dial Tone on Incoming Seize (Yes/No) . . . . . . . . . . . No |
|Minimum Flash Timer (100-250 msec) . . . . . . . . . . . . 250 |
|Maximum Flash Timer (200-800 msec) . . . . . . . . . . . . 200 |
| |
| Outgoing Parameters |
| |
|Outpulse Delay Timer (100-2000msec). . . . . . . . . . . . 800 |
|Outgoing Start Type (Wink/Immediate/Delay/Delay Integ) . . Wink |
|Supv Timer (200-12750msec) . . . . . . . . . . . . . . . . 200 |
|Maximum Wink Timer (300-4000msec). . . . . . . . . . . . . 400 |
|Minimum Wink Timer (50-150msec). . . . . . . . . . . . . . 100 |
|Guard Timer (100-6000msec) . . . . . . . . . . . . . . . . 500 |
|Flash Timer (200-700 msec in 50msec increments). . . . . . 300 |
| |
| Supervision Parameters |
| |
|Fake Answer Supervision After Outpulsing (Yes/No). . . . . Yes |
|Ignore Answer Supervision (Yes/No) . . . . . . . . . . . . No |
|Release Supervision Expected (Yes/No). . . . . . . . . . . No |
|Audio Inhibit Until Answer Supervision (Yes/No). . . . . . No |
|Drop Digit Rcvr for Outgoing Audio Before Ans Sup (Yes/No) No |
| |
| Transmission Parameters |
| |
|Far End Connection |
| (Main PBX/Satellite PBX/Local Office/Toll Office) . . Main PBX |
| Facility Type (Digital/Combination). . . . . . . . . . . . Combination |
|---|
| LINK DESCRIPTOR ASSIGNMENT |
| |
|Digital Link Descriptor Number: 10 |
| |
| Description | Value |
|------------------------------------------------------------------------------|
|Address for Message Control (A/B). . . . . . . . . . . . . |
|BER - Maintenance Limit, 10**-n, n=(3,4,5,6) . . . . . . . 4 |
|BER - Service Limit, 10**-n, n=(3,4,5,6) . . . . . . . . . 3 |
|Data Call Alternate Digit Inversion (Yes/No) . . . . . . . Yes |
|Framing Losses in 24 hrs - Maintenance Limit (0-9000). . . 255 |
|Framing Losses in 24 hrs - Service Limit (0-9000). . . . . 9000 |
|Integrated Digital Access . . . . . . . . . . . . . . . . T1D4 |
|QSIG Private Network Access (Yes/No) . . . . . . . . . . . No |
|Vendor Inter-working Type . . . . . . . . . . . . . . . . . |
|Satellite Link Delay (Yes/No). . . . . . . . . . . . . . . No |
|Slip Rate - Maintenance Limit (0-9000) . . . . . . . . . . 255 |
|Slip Rate - Service Limit (0-9000) . . . . . . . . . . . . 7000 |
|Termination Mode (NT/LT). . . . . . . . . . . . . . . . . . |
|Send Malicious Call Indication to PSTN For Tagged Calls . . No |
| |
| DS1 Parameters: |
|Alarm Debounce Timer - Service Limit (300-3200). . . . . . 500 |
|B8ZS Zero Code Suppression - (Yes/No). . . . . . . . . . . Yes |
| |
| Universal T1 and Enhanced Dual T1 Card only: |
|Operation Mode (CSU/DSX-1) . . . . . . . . . . . . . . . . DSX-1 |
|CSU Tx Line Build-Out(0,7.5,15,22.5 db). . . . . . . . . . |
|DSX-1 line Length(0-133,134-266,267-399,400-533,534-655 ft) 0-133 |
|Extended Super Frame (Yes/No). . . . . . . . . . . . . . . Yes |
|Inverted D channel ( DPNSS only ) (Yes/No) . . . . . . . . No |
| |
| Universal E1 and Enhanced Dual E1 only: |
|CRC-4 enabled(Yes,No). . . . . . . . . . . . . . . . . . . No |
|E1 line Length(0-133,134-266,267-399,400-533,534-655 ft) . 0-133 |
|E1 Impedance (75,120 ohms) . . . . . . . . . . . . . . . . 120 |
| |
| Italian Parameters: |
|Digital Link Fault Delay Timer (0-360 sec) . . . . . . . . 240 |
| |
| Universal T1/E1 Coding Conversion Parameters: |
|Voice conversion (Nil/ADI/Invert/Inverted ADI). . . . . . . Nil |
| Data conversion (Nil/ADI/Invert/Inverted ADI). . . . . . . Nil |
|---|
Asterisk:
wanpipe1.conf
#================================================
#================================================
[devices]
wanpipe1 = WAN_AFT, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 2
PCIBUS = 4
FE_MEDIA = T1
FE_LCODE = B8ZS
FE_FRAME = ESF
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
ACTIVE_CH = ALL
TE_HIGHIMPEDANCE = NO
LBO = 0-110FT
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 9000
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 0
[w1g1]
ACTIVE_CH = ALL
TDMV_ECHO_OFF = NO
zaptel.conf
span=1,1,0,esf,b8zs
e&m=1-24
#bchan=1-23
#dchan=24
loadzone=us
defaultzone=us
zapata.conf
[trunkgroups]
[channels]
language=en
context=from-internal
switchtype=qsig
rxwink=300 ; Atlas seems to use long (250ms) winks
;usedistinctiveringdetection=yes
callerid=asreceived
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
rxgain=0.0
txgain=0.0
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
signalling=em_w
group=1
channel => 1-24
;Include genzaptelconf configs
#include zapata-auto.conf
;Include AMP configs
#include zapata_additional.conf
Fixed!!!
Got it all working, and have CID working aswell. Thanks for the help?
good news, and you’re welcome. thanks for telling everyone how you did it. and for the wiki entry.
Don’t worry. It’s coming. Have to get all my documentation together.