hey,
i’ve been having a really frustrating problem with this tdm400p card with 1 FXO module installed in slot 1.
The card is detected by the computer, but it cannot “see” the FXO module.
The card is shown in the output of lspci:
and this is the relevant output from dmesg when the drivers are loaded:
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.11
Zaptel Echo Canceller: MG2
ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 4 (level, low) -> IRQ 4
Freshmaker version: 73
Freshmaker passed register test
Module 0: Not installed
Module 1: Not installed
Module 2: Not installed
Module 3: Not installed
wctdm: probe of 0000:00:0a.0 failed with error -5
here is my zaptel.conf
fxsks=1
loadzone=uk
defaultzone=uk
and finally the output from ztcfg:
[code]mark@oldbox:~$ sudo ztcfg -vvv
Zaptel Version: 1.4.11
Echo Canceller: MG2
Configuration
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
1 channels to configure.
ZT_CHANCONFIG failed on channel 1: No such device or address (6)[/code]
i heard that there might have been irq conflicts with the card, and have made sure it is on it’s own irq, but that hasn’t helped.
i’ve tried the card in two machines, same problem. both have pci 2.2 5v 32bit slots.
i’ve tried the module in various slots on the card, and the card in various pci slots. i’ve also tried another module.
i’m using debian etch and zaptel 1.4 compiled from source, also tried the debian zaptel 1.2 package to no effect.
can anyone shed some light on what the problem might be?
thanks
PS. full output from lspci and dmesg
lspci:
[code]mark@oldbox:~$ sudo lspci -vvvv
Password:
00:00.0 Host bridge: ALi Corporation M1647 Northbridge [MAGiK 1 / MobileMAGiK 1] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [b0] AGP version 2.0
Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e6000000-e7dfffff
Prefetchable memory behind bridge: e7f00000-efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: Memory at e5800000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if fa)
Subsystem: ASUSTeK Computer Inc. A7A266 Motherboard IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at d400 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at e4800000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+]
Subsystem: ALi Corporation ALi M1533 Aladdin IV/V ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b1d9:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at e3800000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Subsystem: Netgear Unknown device 311a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b400 [size=256]
Region 1: Memory at e3000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
01:00.0 VGA compatible controller: nVidia Corporation NV15DDR [GeForce2 Ti] (rev a4) (prog-if 00 [VGA])
Subsystem: Unknown device 163e:7227
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at e7ff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>[/code]
dmesg:
[code]mark@oldbox:~$ dmesg
Linux version 2.6.18-5-486 (Debian 2.6.18.dfsg.1-13) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Fri Jun 1 00:07:22 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131052
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126956 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f78b0
ACPI: RSDT (v001 ASUS A7A266 0x42302e31 MSFT 0x31313031) @ 0x1ffec000
ACPI: FADT (v001 ASUS A7A266 0x42302e31 MSFT 0x31313031) @ 0x1ffec080
ACPI: BOOT (v001 ASUS A7A266 0x42302e31 MSFT 0x31313031) @ 0x1ffec040
ACPI: DSDT (v001 ASUS A7A266 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
Detected 1477.421 MHz processor.
Built 1 zonelists. Total pages: 131052
Kernel command line: root=/dev/hda2 ro
Local APIC disabled by BIOS – you can enable it with "lapic"
mapped APIC to ffffd000 (01402000)
Enabling fast FPU save and restore… done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512208k/524208k available (1499k kernel code, 11356k reserved, 599k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay using timer specific routine… 2956.85 BogoMIPS (lpj=5913716)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
Enabling disabled K7/SSE Support.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon™ XP1700+ stepping 02
Checking ‘hlt’ instruction… OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c98)
checking if image is initramfs… it is
Freeing initrd memory: 4238k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1170, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [_SB_.PCI0] bus is 0
PCI quirk: region e400-e43f claimed by ali7101 ACPI
PCI quirk: region e800-e81f claimed by ali7101 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PRT]
ACPI: PCI Interrupt Routing Table [_SB.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 © Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:02: ioport range 0xe800-0xe81f has been reserved
pnp: 00:02: ioport range 0x40b-0x40b has been reserved
pnp: 00:02: ioport range 0x480-0x48f has been reserved
pnp: 00:02: ioport range 0x4d6-0x4d6 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e6000000-e7dfffff
PREFETCH window: e7f00000-efffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x3a set to 0x1
audit: initializing netlink socket (disabled)
audit(1214658812.880:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 256k freed
Time: tsc clocksource has been installed.
ACPI: Invalid PBLK length [5]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:04.0
ACPI: Unable to derive IRQ for device 0000:00:04.0
ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0…
ohci_hcd: 2005 April 22 USB 1.1 ‘Open’ Host Controller (OHCI) Driver (PCI)
hda: WDC WD600BB-00CCB0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1…
hdc: SAMSUNG CD-R/RW SW-216B Q001 20010913, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG DVD-ROM SD-616F, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
eth0: RTL8169s/8110s at 0xe0836000, 00:0f:b5:06:6f:62, IRQ 10
ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKI] -> GSI 7 (level, low) -> IRQ 7
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 7, io mem 0xe5800000
hda: max request size: 128KiB
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 <ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKE] -> GSI 3 (level, low) -> IRQ 3
ohci_hcd 0000:00:06.0: OHCI Host Controller
ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:06.0: irq 3, io mem 0xe4800000
hda5 >
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using ohci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: CHESEN USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:02.0-2
input: CHESEN USB Keyboard as /class/input/input1
input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:02.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 © Dave Jones
agpgart: Detected ALi M1647 chipset
agpgart: AGP aperture is 128M @ 0xf0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.4.11
Zaptel Echo Canceller: MG2
ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted.
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 4 (level, low) -> IRQ 4
Freshmaker version: 73
Freshmaker passed register test
Module 0: Not installed
Module 1: Not installed
Module 2: Not installed
Module 3: Not installed
wctdm: probe of 0000:00:0a.0 failed with error -5
input: PC Speaker as /class/input/input2
Real Time Clock Driver v1.12ac
CSLIP: code copyright 1989 Regents of the University of California
Floppy drive(s): fd0 is 1.44M
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
FDC 0 is a post-1991 82077
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
ts: Compaq touchscreen protocol output
Adding 489940k swap on /dev/hda5. Priority:-1 extents:1 across:489940k
EXT3 FS on hda2, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
r8169: eth0: link up
ztdummy: RTC rate is 1024
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present[/code]