Hello All
I’m hoping someone can help me get this going. I can’t 
I have a Trixbox 2.6 with all latest Zaptel drivers installed.
It’s a brand new install as i thought it might have been my old install.
The card i have is a TDM400P with two FXS & two FXO ports.
The two FXS (green) are in ports 1 & 2, the FXO (Red) are in 3 & 4
I can’t get any dial tone on either FXS port, all lights are on, i can get incomming calls.
I have found i can dial the phone from my voip phone on either port 1 or 2.
Once i dial it, i get a Dial tone on port 2 but now 1, though i can;t make calls out. after a minute left alone the dial tone goes away again.
when it rings it’s not the normal ring, it’s more a beep
I’m getting a few Power alarm on module 2, resetting!
BTW the power cable is plugged into the card. i have tried a different PSU also.
Below is my configs.
zaptel.conf
Autogenerated by /usr/sbin/genzaptelconf — do not hand edit
Zaptel Configuration File
This file is parsed by the Zaptel Configurator, ztcfg
It must be in the module loading order
Span 1: WCTDM/0 “Wildcard TDM400P REV I Board 1” (MASTER)
fxoks=1
fxoks=2
fxsks=3
fxsks=4
Global data
loadzone = au
defaultzone = au
zapata-auto.conf
; Autogenerated by /usr/sbin/genzaptelconf — do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: WCTDM/0 “Wildcard TDM400P REV I Board 1” (MASTER)
;;; line="1 WCTDM/0/0 FXOKS (In use)"
signalling=fxo_ks
callerid=“Channel 1” <6001>
mailbox=6001
group=5
context=from-internal
channel => 1
callerid=
mailbox=
group=
context=default
;;; line="2 WCTDM/0/1 FXOKS (In use)"
signalling=fxo_ks
callerid=“Channel 2” <6002>
mailbox=6002
group=5
context=from-internal
channel => 2
callerid=
mailbox=
group=
context=default
;;; line="3 WCTDM/0/2 FXSKS (In use)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 3
context=default
;;; line="4 WCTDM/0/3 FXSKS (In use)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 4
context=default
zapata.conf
;
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
;echotraining=800
rxgain=0.0
txgain=0.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-auto.conf
group=1
;Include AMP configs
#include zapata_additional.conf
zapata_additional.conf
; do not edit this file, this is an auto-generated file by freepbx
; all modifications must be done from the web gui
;;;;;;[6001]
signalling=fxo_ks
record_out=Adhoc
record_in=Adhoc
mailbox=6001@device
immediate=no
echotraining=800
echocancelwhenbridged=no
echocancel=yes
dial=ZAP/1
context=from-internal
callprogress=no
callerid=device <6001>
busydetect=no
busycount=7
accountcode=
channel=>1
;;;;;;[6002]
signalling=fxo_ks
record_out=Adhoc
record_in=Adhoc
mailbox=6002@device
immediate=no
echotraining=800
echocancelwhenbridged=no
echocancel=yes
dial=ZAP/2
context=from-internal
callprogress=no
callerid=device <6002>
busydetect=no
busycount=7
accountcode=
channel=>2
Also Below is what i get when i run ztcfg -vv and genzaptelconf -l
[trixbox1.up2date.net.au ~]# ztcfg -vv
Zaptel Version: 1.4.10
Echo Canceller: OSLEC
Configuration
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
4 channels to configure.
[trixbox1.up2date.net.au ~]# genzaptelconf -l
Span 1: WCTDM/0 “Wildcard TDM400P REV I Board 1” (MASTER)
1 FXS
2 FXS
3 FXO
4 FXO
I’m not sure what i’ve done wrong if anything.
Any help will be great. so thanks in advance.