TDM400p PCI CARD FXS has no dial tone

Hi all

I am using TDM400p PCI card and it has one FXS card. I have connected an analog phone to it. it has no dialtone

The output of [root@localhost ~]# dahdi_scan

[1] active=yes alarms=OK description=Wildcard TDM400P REV E/F Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV E/F location=PCI Bus 03 Slot 06 basechan=1 totchans=4 irq=58 type=analog port=1,FXS port=2,none port=3,none port=4,none

[root@localhost ~]# dahdi_hardware

[root@localhost ~]# dahdi_cfg -vvvvv

[code]DAHDI Tools Version - 2.4.1

DAHDI Version: 2.4.1.2
Echo Canceller(s): MG2
Configuration

Channel map:

Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)

1 channels to configure.

Setting echocan for channel 1 to mg2
[/code]

localhost*CLI> dahdi show channels

Chan Extension Context Language MOH Interpret Blocked State pseudo default default In Service 1 from-internal default In Service

localhost*CLI> dahdi show channel 1

Channel: 1 File Descriptor: 20 Span: 1 Extension: Dialing: no Context: from-internal Caller ID: 4001 Calling TON: 0 Caller ID name: Channel 1 Mailbox: 4001 Destroy: 0 InAlarm: 0 Signalling Type: FXO Kewlstart Radio: 0 Owner: <None> Real: <None> Callwait: <None> Threeway: <None> Confno: -1 Propagated Conference: -1 Real in conference: 0 DSP: no Busy Detection: no TDD: no Relax DTMF: no Dialing/CallwaitCAS: 0/0 Default law: ulaw Fax Handled: no Pulse phone: no DND: no Echo Cancellation: 128 taps (unless TDM bridged) currently OFF Wait for dialtone: 0ms Actual Confinfo: Num/0, Mode/0x0000 Actual Confmute: No Hookstate (FXS only): Onhook

chan_dahdi.conf

[code][channels]
usecallerid=yes
hidecallerid=no
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=yes
busydetect=no
busycount=5
rxgain=0.0
txgain=0.0
immediate=no

#include chan_dahdi_additional.conf
#include dahdi-channels.conf

[/code]

chan_dahdi_additional.conf

;;;;;;[4001] signalling=fxo_ks pickupgroup= mailbox=4001@device immediate=no echotraining=800 echocancelwhenbridged=no echocancel=yes context=from-internal callprogress=no callgroup= callerid=4001 <4001> busydetect=no busycount=7 accountcode= channel=>1

dahdi-channels.conf

; Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER) ;;; line="1 WCTDM/4/0 FXOKS (In use) (SWEC: MG2)" signalling=fxo_ks callerid="Channel 1" <4001> mailbox=4001 group=5 context=from-internal channel => 1 callerid= mailbox= group= context=default

system.conf

[code]# Span 1: WCTDM/4 “Wildcard TDM400P REV E/F Board 5” (MASTER)
fxoks=1
echocanceller=mg2,1

channel 2, WCTDM/4/1, no module.

channel 3, WCTDM/4/2, no module.

channel 4, WCTDM/4/3, no module.

Global data

loadzone = us
defaultzone = us
[/code]

These are the outputs and configurations I have given. When I dial from sip phone FXS is ringing…But it is ringing like continous ring…Not able to attend the call. after that the whole system will get hangup.

Now I am using asterisk 1.4,Dahdi-2.4 version. I have also tried with asterisk 1.8,DAHDI-2.8 upto dahdi-2.10 version. But the same issue is coming.

Anyone Please help me to sort out the problem.

Thanking You
Jeetha P J

Configuration is OK . Maybe you have hardware problem with your fxs module . ( usually fxs ports dont work normally after you connect them to PSTN line instead of Phone )

Hi

I have a ip08 board. I have checked this fxs module in this ip08 board its working fine and I am getting dial tone also