AudioCodes MP11x FXO

Hi - Wondering if anyone can help with a FXO gateway. I’ve had no luck finding docs on getting it working…I think most problems are on the gateway, since the device shows registered, but it’s not passing calls to *.

TIA.

Hello,
please try post the details about your problem, we have an MP fxo sip that is working very well with an Asterisk 1.2.7.1, so I think I can try help you.

Regards.

Marco Bruni

Marco - I think I may have it under control, since I’m now able to make incoming/outgoing calls. I had to play with a lot of different settings. Right now, I’m having a problem with the timing of hangups, etc. The gateway seems to keep the line open too long. Did you have to setup any special settings in the config?

Hello,
you should check if the fxo channel is understanding the disconnection “event” sent from your pbx, your pbx could send an interruption of the signal on the wire, a disconnection tone or just silence, so the MP has to be configured accordingly; in Italy the most common case is the pbx send a disconnect tone, so you have to configure the MP to recognize it, through the call progress tones file, see chapter 16 of the manual; check the parameters of the group “Disconnection and Answer Supervision”, section “Advanced Parameters” -> “General Parameters” to use the other ways to recognize disconnection.

Regards.

Marco Bruni

Were having problems configuring our Audiocodes MP118 fxo. Tech support from our supplier isn’t helping either. Is there any chance I could get a copy of a working .ini file from one of you guys that has the 11x playing nice with Asterisk ?

This is the configuration of an MP fxo that is working well with an Asterisk pbx (more than 50000 calls sice April !):

-----START-----
;**************
;** Ini File **
;**************

;Board: MP-108 FXO
;Serial Number: 529961
;Slot Number: 1
;Software Version: 4.60A.016.003
;Board IP Address: 192.168.0.18
;Board Subnet Mask: 255.255.255.0
;Board Default Gateway: 192.168.0.2
;Ram size: 16M Flash size: 4M
;Num DSPs: 2 Num DSP channels: 8
;Profile: NONE
;------------------------------

[SYSTEM Params]

DisableSNMP = 1
SyslogServerIP = 192.168.0.57

[BSP Params]

[ATM Params]

[Analog Params]

LifeLineType = 1
MinFlashHookTime = 25
FXOLoopCharacteristicsFilename = 'MP1xx10-2-16khz-TBR21-fxo.dat’
CallProgressTonesFilename = 'ita_tones.dat’
FlashHookPeriod = 190

[ControlProtocols Params]

[MGCP Params]

[MEGACO Params]

[SS7 Params]

[Voice Engine Params]

VoiceVolume = 1
MFTransportType = 2
FaxRelayRedundancyDepth = 2
FaxRelayEnhancedRedundancyDepth = 2

[WEB Params]

LogoWidth = ‘339’

[SIP Params]

MAXDIGITS = 7
TIMEBETWEENDIGITS = 5
ISDTMFUSED = 1
REGISTRATIONTIME = 3600
ISPROXYUSED = 1
ISREGISTERNEEDED = 1
AUTHENTICATIONMODE = 1
ISTWOSTAGEDIAL = 0
ENABLEHOLD = 1
CDRREPORTLEVEL = 1
GWDEBUGLEVEL = 5
GATEWAYVERSION = '4.6.0.28’
PROXYNAME = '192.168.0.19’
SIPGATEWAYNAME = '192.168.0.18’
USERNAME = 'mp_fxo’
CNONCE = '0a123bcf’
PASSWORD = '250’
ENABLEVOICEDETECTION = 1
PROGRESSINDICATOR2IP = 1
ALTROUTINGTEL2IPMODE = 0
ISFAXUSED = 1
SUBSCRIPTIONMODE = 1
ENABLETRANSFER = 1
CODERNAME = g729,20
CODERNAME = g711Ulaw64k,20
PREFIX = 10,192.168.0.251,,0
PREFIX = 20,192.168.0.250,
,0
PSTNPREFIX = ,1,,*,0
TRUNKGROUP_1 = 1-8,201,0
PROXYIP = 192.168.0.19
AUTHENTICATION_0 = mp_fxo,250
AUTHENTICATION_1 = mp_fxo,250
AUTHENTICATION_2 = mp_fxo,250
AUTHENTICATION_3 = mp_fxo,250
AUTHENTICATION_4 = mp_fxo,250
AUTHENTICATION_5 = mp_fxo,250
AUTHENTICATION_6 = mp_fxo,250
AUTHENTICATION_7 = mp_fxo,250
TRUNKGROUPSETTINGS = 1,1
TXDTMFOPTION = 4
GWLoggerFlags = lgr_flow,D2
GWLoggerFlags = lgr_psbrdif,D2
GWLoggerFlags = lgr_psbrdex,2
GWLoggerFlags = lgr_stack,D2
GWLoggerFlags = lgr_stk_ses,D2
GWLoggerFlags = lgr_stk_mngr,D2

[VXML Params]

[Audio Staging Params]

[PSTN-SDH Params]

-----STOP-----

Regards.

Marco Bruni

hi,

i have the asterisk 1.2.7.1 . it works fine, i have audiocodes MP-108 fxo. trying to configure the ports as a extension of the Asterisk. i configured a port and it has got registered with asterisk. i did not get the dial tone and even unable to call and receive the calls. please find my ini file…

Please check and help to fix the issues…

;**************
;** Ini File **
;**************

;Board: MP-108 FXO
;Serial Number: 289445
;Slot Number: 0
;Software Version: 4.40.200.371
;Board IP Address: 192.168.1.75
;Board Subnet Mask: 255.255.255.240
;Board Default Gateway: 192.168.1.65
;Profile: NONE
;(null)
;------------------------------

[SYSTEM Params]

SyslogServerIP = 10.1.1.89
EnableSyslog = 0
VXMLFIleName = ''
SaveConfiguration = 1

[BSP Params]

EthernetPhyConfiguration = 4
EnableLANWatchdog = 1

[ATM Params]

[Analog Params]

MinFlashHookTime = 300
FXOLoopCharacteristicsFilename = 'MP1xx10-2-16khz-TBR21-fxo.dat’
FarEndDisconnectSilenceMethod = 255
FarEndDisconnectSilencePeriod = 120
CallProgressTonesFilename = ‘usa_tones_11.dat’

[ControlProtocols Params]

MGCPDTMFDetectionPoint = 0
ProvisionedCallAgents = 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0, 0.0.0.0
ProvisionedCallAgentsPorts = 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
ControlDiffServ = 0

[MGCP Params]

[MEGACO Params]

DIGITMAPPING = ‘’

[SS7 Params]

[Voice Engine Params]

DSPVersionTemplateNumber = 2
VoicePromptsFileName = ''
EnableSilenceCompression = 0
EnableEchoCanceller = 1
VoiceVolume = 1
InputGain = 0
BrokenConnectionEventTimeout = 100
DTMFVolume = -11
DTMFTransportType = 3
MFTransportType = 3
CallerIDTransportType = 3
CallerIDType = 0
FaxTransportMode = 1
V22ModemTransportType = 2
V23ModemTransportType = 2
V32ModemTransportType = 2
V34ModemTransportType = 2
FaxRelayMaxRate = 5
FaxRelayECMEnable = 1
FaxRelayRedundancyDepth = 0
FaxRelayEnhancedRedundancyDepth = 4
FaxModemBypassCoderType = 0
FaxModemBypassM = 1
BasicRTPPacketInterval = 0
CNGDetectorMode = 0
DJBufMinDelay = 70
DJBufOptFactor = 7
RTPRedundancyDepth = 0
RTPPackingFactor = 1
RTPDirectionControl = 0
RFC2833PayloadType = 96
RFC2833TxPayloadType = 96
RFC2833RxPayloadType = 96
RFC2198PayloadType = 104
FaxBypassPayloadType = 102
EnableStandardSIDPayloadType = 0
FlashhookPeriod = 700
EnableAnswerDetector = 1
AnswerDetectorActivityDelay = 0
AnswerDetectorSilenceTime = 10
AnswerDetectorRedirection = 1
AnswerDetectorSensitivity = 0
AnalogSignalTransportType = 0
PrerecordedTonesFileName = ‘’

[WEB Params]

LogoFileName = ''
BKGImageFIleName = ''
LogoWidth = ‘339’

[SIP Params]

ENABLECALLERID = 1
MAXDIGITS = 10
NUMBEROFWAITINGINDICATIONS = 4
ALWAYSUSEROUTETABLE = 0
ENABLECALLWAITING = 1
TIMEBETWEENWAITINGINDICATIONS = 10
TIMEBETWEENDIGITS = 4
TIMEFORDIALTONE = 16
LOCALSIPPORT = 5060
OUTOFBANDDTMFFORMAT = 2
PLAYRBTONE2IP = 0
ISDTMFUSED = 1
ISSPECIALDIGITS = 1
REGISTRATIONTIME = 3600
SIPT1RTX = 500
SIPT2RTX = 4000
ISPROXYUSED = 1
ISREGISTERNEEDED = 1
AUTHENTICATIONMODE = 0
SIPDESTINATIONPORT = 5060
PLAYRBTONE2TEL = 2
ISTWOSTAGEDIAL = 1
DETFAXONANSWERTONE = 0
ROUTEMODETEL2IP = 0
ENABLECURRENTDISCONNECT = 1
ENABLEREVERSALPOLARITY = 1
SECURECALLSFROMIP = 0
ENABLEBUSYOUT = 1
ENABLEHOLD = 1
ENABLEFORWARD = 1
CDRREPORTLEVEL = 2
MAXACTIVECALLS = 8
CHANNELSELECTMODE = 0
GWDEBUGLEVEL = 5
ENABLEPROXYKEEPALIVE = 1
ENABLEEARLYMEDIA = 1
ISUSERPHONE = 1
SIPSESSIONEXPIRES = 0
DEFAULTNUMBER = '1000’
PROXYNAME = ''
REGISTRARIP = '192.168.1.100’
SIPGATEWAYNAME = ''
USERNAME = ''
CNONCE = ''
PASSWORD = ''
ENABLESILENCEDISCONNECT = 0
DEFAULTRELEASECAUSE = 3
PROGRESSINDICATOR2IP = -1
RXDTMFOPTION = 3
ISFALLBACKUSED = 1
ALWAYSSENDTOPROXY = 1
ISPROXYHOTSWAP = 1
PROXYKEEPALIVETIME = 60
PROXYREDUNDANCYMODE = 0
FILTERCALLS2IP = 0
PRACKMODE = 1
PROXYHOTSWAPRTX = 3
GWAPPDELAYTIME = 5
SIPMAXRTX = 7
ENABLEDIDWINK = 0
DISCONNECTONBROKENCONNECTION = 1
STUTTERTONEDURATION = 2000
ENABLEDIGITDELIVERY = 1
WAITINGBEEPDURATION = 300
SENDINVITETOPROXY = 1
XFERPREFIX = ''
CDRSYSLOGSERVERIP = 0.0.0.0
REGISTRATIONRETRYTIME = 30
MWIEXPIRATIONTIME = 7200
SUBSCRIBERETRYTIME = 120
ENABLEMWISUBSCRIPTION = 1
MWISERVERIP = 0.0.0.0
ISTRUSTEDPROXY = 1
ASSERTEDIDMODE = 0
MWIANALOGLAMP = 1
MWIDISPLAY = 1
ENABLEMWI = 1
USEGATEWAYNAMEFOROPTIONS = 0
ISUSERPHONEINFROM = 0
ADDTON2RPI = 0
PREFERROUTETABLE = 1
USESOURCENUMBERASDISPLAYNAME = 1
MINSE = 90
ENABLEDIGITDELIVERY2IP = 1
IPALERTTIMEOUT = 180
ISFAXUSED = 1
HOLDFORMAT = 1
ENABLEPROXYSRVQUERY = 1
GWREGISTRATIONNAME = ''
TIMEBEFOREWAITINGINDICATIONS = 0
MAXCALLDURATION = 0
REGISTRARNAME = 'Audiocodes_sip’
REGISTRATIONTIMEDIVIDER = 50
HOTLINETONEDURATION = 16
ENABLETRANSFER = 1
CODERNAME = g729,20
CODERNAME_1 = g729,20
CALLERDISPLAYINFO0 = 298,0
PREFIX = ,192.168.1.100,,0
TRUNKGROUP = 1-1,298,0
PROXYIP = 192.168.1.100
AUTHENTICATION_0 = 298,blah
TXDTMFOPTION = 4
TELPROFILE_1 = Default Tel Profile,1,0,1,70,7,0,0,-11,0,1,1,0,1,1

[VXML Params]

[IPsec Params]

[Audio Staging Params]

[PSTN-SDH Params]

Any help would be appreciated…

Thanks in advance