I have followed this documentation to install Asterisk With Sangoma Hardware Telephony Cards for Asterisk - Telephony Cards - Documentation
But I am using Centos 7
Everything went well with the installation.
The problem is that when I use dahdi_cfg -vvv I get:
DAHDI Tools Version - 3.2.0
DAHDI Version: 3.2.0
Echo Canceller(s):
Configuration
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 02)
Channel 03: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 03)
Channel 04: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 04)
Channel 05: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 05)
Channel 06: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 06)
Channel 07: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 07)
Channel 08: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 08)
Channel 09: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 09)
Channel 10: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 10)
Channel 11: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 11)
Channel 12: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 12)
Channel 13: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 13)
Channel 14: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 14)
Channel 15: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 15)
Channel 16: D-channel (Default) (Echo Canceler: none) (Slaves: 16)
Channel 17: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 17)
Channel 18: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 18)
Channel 19: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 19)
Channel 20: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 20)
Channel 21: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 21)
Channel 22: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 22)
Channel 23: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 23)
Channel 24: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 24)
Channel 25: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 25)
Channel 26: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 26)
Channel 27: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 27)
Channel 28: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 28)
Channel 29: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 29)
Channel 30: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 30)
Channel 31: CAS / User (Default) (Echo Canceler: mg2) (Slaves: 31)
31 channels to configure.
DAHDI_SPANCONFIG failed on span 1: No such device or address (6)
Here is the output of some commands:
lspci | grep Sangoma
02:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card
wanrouter status
Devices currently active:
wanpipe1
Wanpipe Config:
Device name | Protocol Map | Adapter | IRQ | Slot/IO | If’s | CLK | Baud rate |
wanpipe1 | N/A | A101/1D/2/2D/4/4D/8/8D/16/16D| 19 | 4 | 1 | N/A | 0 |
Wanrouter Status:
Device name | Protocol | Station | Status |
wanpipe1 | AFT TE1 | N/A | Connected |
dahdi_hardware
pci:0000:02:04.0 wanpipe- 1923:0040 Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card
wanrouter hwprobe
| Wanpipe Hardware Probe Info |
|---|
| 1 . AFT-A101-SH : SLOT=4 : BUS=2 : IRQ=19 : CPU=A : PORT=1 : HWEC=32 : V=40 |
Sangoma Card Count: A101-2=1
lsmod | grep dahdi
dahdi 227916 1 wanpipe
crc_ccitt 12707 1 dahdi
lsmod | grep wan
wanec 396153 0
af_wanpipe 39708 0
wanpipe 1164057 1
wanrouter 62347 5 af_wanpipe,wanec,wanpipe
sdladrv 260014 4 af_wanpipe,wanec,wanrouter,wanpipe
dahdi 227916 1 wanpipe
here is the content of my dahdi system.conf:
Autogenerated by /sbin/dahdi_genconf on Wed Jul 12 14:23:53 2023
If you edit this file and execute /sbin/dahdi_genconf again,
your manual changes will be LOST.
Dahdi Configuration File
This file is parsed by the Dahdi Configurator, dahdi_cfg
Global data
span=1,1,0,cas,hdb3
cas=1-15:1101
dchan=16
cas=17-31:1101
echocanceller=mg2,1-15,17-31
loadzone = ar
defaultzone = ar
I have build the system.conf manually as it is generated empty by dahdi_genconf
I have been working on this for a couple of days and do not know how to proceed.
Thanks for the help in advance
Karim.