# Driver Issues?

**URL:** <https://community.asterisk.org/t/driver-issues/3589>\
**Category:** Asterisk Support\
**Created:** [January 10, 2006, 9:07pm UTC](https://community.asterisk.org/t/driver-issues/3589 "2006-01-10T21:07:18Z")\
**Posts on this page:** 11\
**Page:** 1

<div class="post-metadata">

**Author:** ![SeA\_orAmor](https://avatars.discourse-cdn.com/v4/letter/s/a698b9/32.png) [@SeA\_orAmor](https://community.asterisk.org/u/SeA_orAmor)\
**Post date:** [January 10, 2006, 9:07pm UTC](https://community.asterisk.org/t/driver-issues/3589/1 "2006-01-10T21:07:18Z")

</div>

I’m running the latest version of Asterisk on a Gentoo box. I have a TE110P and a TDM400P. Make and make install worked fine for libpri, zaptel and asterisk. I get no errors doing a modprobe on zaptel, wcte11xp, and wctdm. However, when I do an lsmod, I get

`voip asterisk # lsmod
Module Size Used by
wctdm 135136 - 
wcte11xp 23872 - 
zaptel 222084 - 
crc_ccitt 1608 - `

ztcfg -vv returns no errors; neither does a verbose start of asterisk.

I’m completely at a loss here. I can make SIP calls, but not any Zap calls, which I assume is because my drivers aren’t loading properly.

Any thoughts?

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 11, 2006, 11:41am UTC](https://community.asterisk.org/t/driver-issues/3589/2 "2006-01-11T11:41:07Z")

</div>

is the green light lit on your TDM400P? if not you have a problem. even if it is lit, you may be sending calls out the wrong ZAP channel. You know how, when you dial, you do DIAL(ZAP/1/${EXTEN}||) ? Well, try changing that 1 to a 2, 3 or 4.

---

<div class="post-metadata">

**Author:** ![SeA\_orAmor](https://avatars.discourse-cdn.com/v4/letter/s/a698b9/32.png) [@SeA\_orAmor](https://community.asterisk.org/u/SeA_orAmor)\
**Post date:** [January 11, 2006, 2:09pm UTC](https://community.asterisk.org/t/driver-issues/3589/3 "2006-01-11T14:09:07Z")

</div>

No, no green light. Just a pulsating red one.

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 11, 2006, 4:17pm UTC](https://community.asterisk.org/t/driver-issues/3589/4 "2006-01-11T16:17:58Z")

</div>

what does digium’s documentation say the red light means? i’ve got a TDM400P but i’ve never seen a red light. worst i’ve had is no green light (meaning the driver had not been loaded.)

---

<div class="post-metadata">

**Author:** ![SeA\_orAmor](https://avatars.discourse-cdn.com/v4/letter/s/a698b9/32.png) [@SeA\_orAmor](https://community.asterisk.org/u/SeA_orAmor)\
**Post date:** [January 11, 2006, 5:47pm UTC](https://community.asterisk.org/t/driver-issues/3589/5 "2006-01-11T17:47:31Z")

</div>

Oops, my bad. I misread your post. I have a pulsing red light on my TE110P. I have four solid green lights on my TDM400P.

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 11, 2006, 7:38pm UTC](https://community.asterisk.org/t/driver-issues/3589/6 "2006-01-11T19:38:32Z")

</div>

well then let’s leave the TE110P for somebody that knows more than i.

if you’ve got 4 green lights and 4 analog lines plugged into 4 FXO modules on your TDM400, then it’s just got to work. you may have not configured [zapata.conf](http://www.voip-info.org/wiki/view/Asterisk+config+zapata.conf) correctly. or [zaptel.conf](http://www.voip-info.org/wiki-Asterisk+config+zaptel.conf). Make sure you’re trying to send calls over the working card and you’ve got the signalling correct. Watch the console to get some clues.

How lost are you exactly 😉❓

---

<div class="post-metadata">

**Author:** ![SeA\_orAmor](https://avatars.discourse-cdn.com/v4/letter/s/a698b9/32.png) [@SeA\_orAmor](https://community.asterisk.org/u/SeA_orAmor)\
**Post date:** [January 11, 2006, 8:48pm UTC](https://community.asterisk.org/t/driver-issues/3589/7 "2006-01-11T20:48:46Z")

</div>

Ok, driver issues appear to be fixed. lsmod returns what I believe is correct information.

I still cannot make Zap calls, but I’m sure there’s some setting I have wrong.

I still have the pulsing red light on my TE110P, however.

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 11, 2006, 10:46pm UTC](https://community.asterisk.org/t/driver-issues/3589/8 "2006-01-11T22:46:19Z")

</div>

An E1/T1/J1 card like the TE110P would require libpri. Did you download that package and compile, install, etc.? If not, get the software from the Asterisk website.

---

<div class="post-metadata">

**Author:** ![SeA\_orAmor](https://avatars.discourse-cdn.com/v4/letter/s/a698b9/32.png) [@SeA\_orAmor](https://community.asterisk.org/u/SeA_orAmor)\
**Post date:** [January 11, 2006, 10:51pm UTC](https://community.asterisk.org/t/driver-issues/3589/9 "2006-01-11T22:51:43Z")

</div>

> [@gtcleaves](#):
>
> An E1/T1/J1 card like the TE110P would require libpri. Did you download that package and compile, install, etc.? If not, get the software from the Asterisk website.

Yup. See first post. 😉

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 11, 2006, 10:54pm UTC](https://community.asterisk.org/t/driver-issues/3589/10 "2006-01-11T22:54:53Z")

</div>

Doh!

Well, unfortunately I’m out of my depth 'cause I’ve never used those cards. Good luck.

---

<div class="post-metadata">

**Author:** ![gtcleaves](https://avatars.discourse-cdn.com/v4/letter/g/65b543/32.png) [@gtcleaves](https://community.asterisk.org/u/gtcleaves)\
**Post date:** [January 12, 2006, 10:42am UTC](https://community.asterisk.org/t/driver-issues/3589/11 "2006-01-12T10:42:20Z")

</div>

SeñorAmor, by your nick you must speak Spanish. Maybe this post will help with the TE110P card:

[asterisk-es.org/modules/sect … le&artid=1](http://www.asterisk-es.org/modules/sections/index.php?op=viewarticle&artid=1)

Maybe your IRQs are in conflict?
